Detailed Product Description

PFC series Generator Sets

Engine: Commins engine

Electrical Specifications

1) Power Factor: 0.8 Lagging

2) 3 Phase 4 Wire

3) Insulation: Class H

4) Brushless

5) Self-Exited

6) IP23 Protection

7) AVR regulation

8) Starting by Battery

Special Specifications

1. Frequency: 50/60Hz

2. 3 Phase 4 Wire

3. Speed: 1500/1800rpm

4. Three Phase Voltage Available: 208V / 220V / 230V / 240V / 380V / 390V / 400V / 415V / 440V / 460V / 480V

Manufacturing Standards:

ISO8528; ISO1105; ISO3046; GB/T2820; GB755; BS5000; NEMAMG-22; YD/T502

SCOPE OF SUPPLY

1. DIESEL ENGINE

1.1 Engine which includes wet type cylinder, direct injection combustion chamber, exhaust turbocharger, water cooling, electronic governor, etc.

1.2 Fuel system, which includes, fuel pump, strainers or filters, etc.

1.3 Air intake and exhaust system, which includes air filter, exhaust silencer, bellow, all intake and exhaust piping, cablings, instruments, valves and settings, etc.

1.4 Cooling system, which includes radiator with water level alarm and indicator, thermostatic switch, thermostatic heater, engine shaft mounted fan, all interconnecting piping, cablings, instruments, valves and settings, etc.

1.5 Lubricating system includes pumps, oil sumps, oil strainers and filters, all interconnecting piping, instruments, valves and settings, etc.

1.6 Starting system, which includes 2 sets of batteries, a set of AC charger, and interconnecting piping, cablings, instrument, valves and settings, etc.

2. AC SYCHRONOUS GENERATOR

 2.1 Generator, which includes exciter, rectifier, AVR, shaft mounted fan if required.

 2.2 All interconnecting piping, cablings, instruments, valves and settings, etc.

3. COUPLINGS AND GUARD

 3.1 Coupling

 3.2 Coupling Guard

4. CONTROL PANEL

 4.1 key start / automatic control panel (AMF), ATS

5. BASEPLATE

 5.1 Common base plate

6. DOCUMENTS

 6.1 Generator Set Installation Manual

 6.2 Generator Set Operation and Maintenance Manual

 6.3 Generator Set Control Panel Manual

 6.4 Engine Manual and Quality File

 6.5 Alternator Manual and Quality File

 6.6 Factory Acceptant Test Report

 6.7 Relative Drawings and Diagrams

INSPECTION AND TEST

1 GENERAL

1.1 Each engine shall be tested at manufacturers workshop to certify the engine output and fuel consumption in accordance with the site operating condition specified by purchaser on the specification datasheet.

1.2 All relevant information drawings pertinent to the testing and test procedure shall be transmitted to the purchaser in advance of the test date notification.

1.3 The purchaser shall call for additional testing if test results are unsatisfactory or marginal. Any equipment rejected shall be repaired or replaced to the purchasers satisfaction and tests shall be repeated.

1.4 Any unsatisfactory material, equipment, installation, or workmanship shall be replaced or repaired to the purchasers satisfaction at the manufacturers cost.

1.5 The engine and generator shall be tested individually in accordance with relevant standards specified above.

1.6 The completed and individually tested engine and generator shall be assembled onto the baseplate with all auxiliaries, instruments and controls for a complete test of the generator set.

Why Cummins powered gensets?

1. Cummins engines which are made in China with the same standard of the US Cummins keep the quality almost the same as the US Cummins.

2. More than 90% of the Engines components and spares are made in China which keeps the cost much lower.

3. Cummins engines are universally just as Cummins factories all around the world; all the spares are universal which make the maintenance and reparation very simple.

4. Cummins has worldwide after-sales network, to whom you can get technical support and spares right near your house.

5. Engineers are more familiar with Cummins engines because they are most wildly use in every filed and everywhere around the world.